工业电源
Click the link below to download the file.
Get your files as below link
Dowload link
24V
240W
10A
18-30 Vdc
124 x 38 x 117 mm
4.88” x 1.50” x 4.61”
0.52 kg (1.15 lb)
|
输出电流
10A
|
|
输出电压
24V
|
|
输出电压范围
17.5-29.5Vdc
|
|
输出电压调整范围
-
|
|
输出功率
240W
|
|
输出电流调整范围
|
|
最大输出电压
|
|
缓冲时间
15 s, 30 s, 45 s, 1 min, 3 min, 5 min, 10 min, 20 min, 30 min, ∞
|
|
线电压调整率
-
|
|
负载调整率
-
|
|
纹波电压
-
|
|
开机时间
-
|
|
保持时间
-
|
|
动态回应
-
|
|
电容性负载启动
-
|
|
摇控开/关
-
|
|
保护设备
-
|
|
输入输出间电压骤降
-
|
|
残留波纹/PARD (20MHz)
-
|
|
残留波纹
-
|
|
最大功率
-
|
|
波纹与噪音
-
|
|
CC 型号 LED系统电压范围
-
|
|
升压时间
-
|
|
峰值功率持续时间
7 seconds
|
|
峰值功率回复时间
5 seconds
|
|
额定输入电压
24 Vdc
|
|
输入电压范围
18-30 Vdc
|
|
最大输入电压
-
|
|
额定输入频率
-
|
|
输入频率范围
|
|
额定直流输入电压
|
|
直流输入电压范围
-
|
|
输入电流
-
|
|
输入功率（待机模式）
-
|
|
100% 负载效率
98% typ.
|
|
涌入电流
-
|
|
充电时间
< 9 hr ± 1 hr (2 A charging current for 24 V/12 AH battery)
|
|
功率因数
-
|
|
漏电流
-
|
|
额定电流
-
|
|
谐波失真总量
-
|
|
功率损耗
-
|
|
效率 @ 10% 负载
-
|
|
底座 / 外壳上盖
Aluminium
|
|
|
指示灯
-
|
|
|
冷却方式
Convection
|
|
|
输入端
-
|
|
|
输出端
-
|
|
|
信号端
-
|
|
|
声压级（SPL）
< 40 dBA
|
|
|
输入/输出端
-
|
|
|
信号
-
|
|
|
安装导轨
Standard TS35 DIN Rail in accordance with EN 60715
|
|
|
电线
Input / Output: AWG 18-8 (Load: 0-5 A), AWG 14-8 (Load: 5-10 A)
Battery: AWG 18-8 (Load: 0-5 A), AWG 14-8 (Load: 5-10 A) Signal: AWG 24-12 |
|
|
保护结构
-
|
|
|
端子台
Input / Output: 4 Pins
Battery: 2 Pins Signal: 8 Pins Temperature Sensor & Rx/Tx: 4 Pins (CVILUX CP3504P1H00-NH) |
|
|
重量
0.52 kg (1.15 lb)
|
尺寸
124 x 38 x
117 mm
4.88” x 1.50” x 4.61” |
|
振动测试（运行状态）
EN 60068-2-64 (Wind Power Application)
|
|
防震测试（运行状态）
-
|
|
运行温度
-40°C to +70°C
|
|
储存温度
-40°C to +85°C
|
|
功率降级
> 60°C de-rate power by 2.5% / °C (when battery is fully charged) If the battery is not fully charged at max load, it is recommended that the surrounding air temperature should not exceed 50°C.
|
|
运行湿度
5 to 95% RH (Non-Condensing)
|
|
防震测试（非运行状态）
IEC 60068-2-27, 30 G (300 m/s²) for a duration of 18 ms, 1 time per direction, 2 times in total
|
|
振动测试（非运行状态）
IEC 60068-2-6, 10 Hz to 500 Hz @ 30 m/s² (3 G peak); 60 min per axis for all X, Y, Z direction
|
|
储藏湿度
-
|
|
运行高度
0 to 6,000 m (Approvals apply only up to 5,000 m)
|
|
污染程度
2
|
|
碰撞试验（运行状态）
-
|
|
过压类别
-
|
|
Corrosion
-
|
|
过压保护
Auto Recovery
|
|
超负载/过电保护
Normal Operation: Auto Recovery
Battery Operation: Latch off |
|
过热保护
Normal Operation: Auto Recovery
Battery Operation: Latch off |
|
短路保护
-
|
|
极性反接保护
-
|
|
防护等级
IP20
|
|
防震保护
Class III
|
|
输入端极性保护
Yes
|
|
电池极性保护
Yes
|
|
电池电压保护错误
Yes, 30 Vdc Max (the maximum voltage that will not cause damage to the unit)
|
|
深度放电保护
Yes (21 V typ.)
|
|
超负载保护
-
|
|
过电保护
-
|
|
内置保险丝
-
|
|
输入欠压保护
Yes
|
|
Safety Certificate
-
|
|
电气安全
CB scheme: IEC 62368-1
TUV Bauart: EN 62368-1 UL/cUL recognized: UL 62368-1 and CAN/CSA C22.2 No. 62368-1 (File No. E131881) EAC: TP TC 002/2011 |
|
CE
In conformance with EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU
|
|
医疗安全
-
|
|
电隔离
Power Port to Housing: 500 Vac
Signal Port to Housing: 500 Vac Power Port to Signal Port: 500 Vac |
|
工业控制设备
-
|
|
危险场所/ATEX
-
|
|
II 3 G ATEX 2014/34/EU
-
|
|
机器电气设备
-
|
|
用於电率安装的电气设备
-
|
|
安全特低电压
-
|
|
海事
-
|
|
材料与部件
-
|
|
隔离电阻
-
|
|
PE 电阻
-
|
|
UKCA
In conformance with Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016
|
|
国家地区证书
-
|
|
BIS
-
|
|
KC
-
|
|
Electrical Equipment for Measurement, Control, and Laboratory Use
-
|
|
ITE Safety
-
|
|
SIL3
-
|
|
排放
CE & RE
EN/BS EN 61000-6-4, EN 61204-3 |
|
抗扰度
EN/BS EN 61000-6-2, EN 61204-3
|
|
谐波电流排放
-
|
|
电压波动和闪变
-
|
|
ESD 抗扰度
-
|
|
辐射抗扰度
-
|
|
EFT
-
|
|
电涌
-
|
|
传导抗扰度
-
|
|
磁场
-
|
|
电压骤降
-
|
|
通用用途之部件供电
-
|
|
额定电池电压
24 Vdc, SLA Sealed lead acid battery
2 x 12 Vdc, SLA Sealed lead acid battery in series |
|
电池电压范围
-
|
|
电池容量
3.4 AH ~ 100 AH
|
|
电池充电模式
-
|
|
充电电压结束
27.6 V
|
|
电池熔断器
-
|
|
电池放电电压范围
21 Vdc ... 27.6 Vdc
30 Vdc Max (the maximum voltage that will not cause damage to the unit) |
|
电池充电电流
0.5 A, 1 A, 1.5 A, 2 A (typ.) (constant current)
|
|
Battery Current Consumption
< 200 mA
|
|
放电电流
-
|
|
建议充电电压
-
|
苏公网安备
32050902101200号